CarlB

Car Builders Solution is a great resource. If I had known about them, I could have saved myself days of screwing around building a switch panel.

Saturday I was at a track event and my instructor was Michael Lysczek. He got me because he was an instructor at Summit Point for your event. He said he really enjoyed the event and wore the shirt because he wanted to show me.

I want to complain about modern car servicing, but I will start by saying that our education system ignores anything except collage preparation, and it does a poor job of that. The English apprentice programs produced some very skilled people, but they shoehorned people as well. Now on to 4Cs. They aren't the only ones, but they were supposed to be selling a sports car. I wanted to turn off the nannies and couldn't figure out how to do it. I have a number of friends that work at Chrysler. I know a lot of the people involved with Viper. They couldn't help me. I don't need the car braking on its own in the middle of a corner.

These two documents might be helpful Caterham7 T2.001.pdf ECU Pinout Zetec T-2.pdf

Yes I am using a Pectel and a Zetec. Happy to help if I can. Hopefully you can get your car together. I haven’t had problems with the engine or the ECU. Plenty of other issues, especially electrical.

Thank you for the more descriptive explanation. If you purchase wires as a universal kit they will come with loose terminals that need to be crimped on the wire before inserting in into the distributor cap. The 7 MM wires with their terminals will fit the cap. If you get 8 MM wires you will need to get adaptors. Older cars used 7 MM wire and the cross flow Ford engine is set up for 7 MM wire.

Make sure you get 7 MM wire. I do not think the 8 MM wire will fit in the cap.

If we want to talk about V-8s for Caterhams, I have a different one that isn't as cool as some of those mentioned but might actually work. Yamaha built an engine for Volvo with a 60-degree bank angle. It has been used in those very reliable Nobles, but I wouldn't blame that on the engine. It is reported on that always reliable site Wikipedia to weigh 416 lbs. The engine was used in Australian super cars maybe Croc can fill us in. Yamaha now builds a 425 HP version for an outboard motor. This engine is direct injected and has a 12 to 1 compression ratio. The fuel requirement is 89 Octane.

My car doesn't have a keyed-on switch. It has a master switch, an ignition switch that isn't obvious, a fuel pump switch, and a starter button. The dash has a number of unmarked switches to figure out. The steering wheel also come off.

Finally ready for the track. I really like my new cage! 1300 pounds exactly with the new transmission that doesn't want to shift into 5th gear. Really looking forward to NJMP.

Are you sure the ECU is damaged? It might be worth a try if you get your wiring and sensors figured out.

Opps - Thanks Croc. Sould have been paying attention. All set with new dates. Glad it isn't later, we are leaving for Europe the following week.

Updated my reservation and will see everyone Saturday evening.

I think we are saying very close to the same thing about the problem. You gave a more detailed description. You could fix the problem with rod-ends or spherical bearings at the chassis mounts, but you would have to change the mounting bolts from horizontal to vertical. To put the spherical bearing at the outer end can probably be done with a custom A-frame. The GM, I think, G body (1980s midsize sedans) used the triangulated four link as well. Croc has a Holden race car with the same suspension.

The A frame twist when the car rolls. When the bushings at both ends require more force than the force required to bend the tube, the tube bends. Eventually the force is enough to break the weld or the tube.

The twisting motion from the car rolling is what breaks the Aframe. Caterham has made rear Aframes with spherical bearings and I do not understand why they changed.

Wide track will make the car faster on track. What do you use the car for? For the street, do you really care that it will generate more grip in the corners?

This is what Ford recommends. HOAT (Hybrid OAT) Silicates & Organic Acids Zerex™ G-05™ Ford, Chrysler, European YELLOW I am not sure it makes a lot of difference if you change it frequently. Zerex also makes coolant that meets all the OEM requirements.

Mercedes pre-war grand prix cars used Nitrobenzene. If you want some really powerful oxygen baring fuel, try Hydrazine. The byproducts of combustion are way more toxic than nitromethane or benzine.

The picture of the lotus 11 shows the high-performance intake manifold from the very early 1960s. The first year or two of the engine there was an aluminum block and a high-performance version of the engine.

If it was mine, I would have it cleaned at a machine shop and new bearings and freeze plugs installed. I would also pull the oil gally plugs. If you do not want to replace the bearings. use a wire brush like a gun cleaning tool and compressed air.

I had a corvette pitted next to me a VIR that had the lithium battery catch fire. Now racetracks are not letting electric cars run. I am just a little leery of them.

That track looks like Waterford Hills with more elevation change. Great Caterham track!

I am not sure these will fit, but Caterham sells a Heavy duty kit that includes new bigger axles, sealed bearings and aluminum hubs. I have them for my car and it uses Spitfire spindles. the part number is HUR2003K

Summit Point must have changed their mind. It is all over the press that they will not allow electric vehicles or hybrids. on track and I think they even have some parking restrictions. They are saying they do not know how to put out the fires.